How Much Does Takeover Boost Attributes 2k22 Current Gen, Michael Tierney Obituary, Which Symbol Is Used To Indicate Safe Lifting Points?, Articles C

Bulk packagings must have exterior heating coils fusion welded to the tank shell which have been properly stress relieved. In addition, a container exceeding 4 fluid ounces volumetric capacity (7.22 cubic inches) or containing more than 65 grams of fuel may not be connected or manifolded to a lighter or similar device and must also be described and packaged according to the fuel contained therein. This is in response to your November 18, 2015 e-mail and subsequent conversations with members of my staff requesting clarification of the Hazardous Materials Regulations (HMR; 49 CFR Parts 171-180) applicable to the selection of a . You can learn more about the process FAR). Refrigerated liquefied gases that are authorized to be transported in portable tanks are specified in tank instruction T75. Regulation Y B35 Tank cars containing hydrogen cyanide may be alternatively marked Hydrocyanic acid, liquefied if otherwise conforming to marking requirements in subpart D of this part. When the word Normal is indicated, 178.275(g)(3) of this subchapter does not apply. The quantities of hazardous materials do not exceed those specified in 173.4a of this subchapter; and. However, button cell batteries installed in equipment (including circuit boards) need not be considered; and, c. The shipping paper must indicate UN 3091 Lithium metal batteries packed with equipment or UN 3481 Lithium ion batteries packed with equipment, as appropriate. If you have comments or suggestions on how to improve the www.ecfr.gov website or have questions about using www.ecfr.gov, please choose the 'Website Feedback' button below. 421 This entry will no longer be effective on January 2, 2023, unless we terminate it earlier or extend it beyond that date by notice of a final rule in the Federal Register. 19 For domestic transportation only, the identification number UN1075 may be used in place of the identification number specified in column (4) of the 172.101 table. (3) B codes. The coal tar pitch compound must be in a solid mass during transportation. Enhanced content is provided to the user to provide additional context. 177 Gasoline, or, ethanol and gasoline mixtures, for use in internal combustion engines (e.g., in automobiles, stationary engines and other engines) must be assigned to Packing Group II regardless of variations in volatility. In addition, a lighter design intended to contain a non-pressurized Class 3 material is excepted from the examination and testing criteria specified in 173.308(b)(3). Unlined tanks must be passivated before being placed in service. 5101-5128, 44701; 49 CFR 1.81, 1.96 and 1.97. A54 Irrespective of the quantity limits in Column 9B of the 172.101 table, a lithium battery, including a lithium battery packed with, or contained in, equipment that otherwise meets the applicable requirements of 173.185, may have a mass exceeding 35 kg if approved by the Associate Administrator prior to shipment. Specifically, you seek clarification on the implementation of special provision IP15which is listed in Column 7 of the 172.101 Hazardous Materials Table (HMT)as it applies when this material is packaged in a composite intermediate bulk container (IBC) with a rigid inner receptacle. The HMT consists of 10 columns and provides information for each hazardous material listed. Cargo heaters must be reverse refrigeration (heat pump) units. 140 This material is regulated only when it meets the defining criteria for a hazardous substance or a marine pollutant. When a plus sign is assigned to mix- TP40 The portable tank must not be transported when connected with spray application equipment. 131 This material may not be offered for transportation unless approved by the Associate Administrator. 347 Effective July 1, 2011, for transportation by aircraft, this entry may only be used if the results of Test series 6(d) of Part I of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) have demonstrated that any hazardous effects from accidental functioning are confined to within the package. B66 Each tank must be equipped with gas tight valve protection caps. The Electronic Code of Federal Regulations (eCFR) is a continuously updated online version of the CFR. D. Class 5 materials An installed inflation cylinder that requires recharging must be filled in accordance with 173.301(l). TP28 A portable tank having a minimum test pressure of 2.65 bar (265 kPa) may be used provided the calculated test pressure is 2.65 bar or less based on the MAWP of the hazardous material, as defined in 178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. As a The fiber drum must to be fabricated with a three ply wall, as a minimum. The HMT provides the basic information necessary to ship a hazardous material safely. 388 a. Lithium batteries containing both primary lithium metal cells and rechargeable lithium ion cells that are not designed to be externally charged, must meet the following conditions: i. 108 Fireworks must be so constructed and packaged that loose pyrotechnic composition will not be present in packages during transportation. 387 When materials are stabilized by temperature control, the provisions of 173.21(f) of this subchapter apply. If you work for a Federal agency, use this drafting For non-pressurized lighters containing a Class 3 (flammable liquid) material, its design, description, and packaging must be approved by the Associate Administrator prior to being offered for transportation or transported in commerce. The manufacturer must provide such information to a representative of the Department upon request. The numbers and letters in the special provisions column are referred to in 49 CFR 172.102 with an explanation of their meanings. TP18 The temperature of this material must be maintained between 18 C (64.4 F) and 40 C (104 F) while in transportation. IBCs are authorized subject to the conditions and limitations of this section provided the IBC type is authorized according to the IBC packaging code specified for the specific hazardous material in Column (7) of the 172.101 Table of this subchapter and the IBC conforms to the requirements in subpart O of part 178 of this subchapter at the . Table 1 authorizes IBCs for specific proper shipping names through the use of IB Codes assigned in the 172.101 table of this subchapter. c. The motor carrier must maintain a satisfactory safety rating as prescribed in 49 CFR part 385. B130 When transported by motor vehicle, used diatomaceous earth filter material is not subject to any other requirements of this subchapter except for the shipping paper requirements of subpart C of part 172 of this subchapter; emergency response information as required by 172.602(a)(2) through (a)(7) of this subchapter; and the marking requirements of 172.302 of this subchapter, if the following requirements are met: a. Packagings are non-DOT specification sift-proof motor vehicles or sift-proof roll-on/roll-off bulk bins, which are covered by a tarpaulin or other equivalent means. The batteries must be securely attached to the interior structure of the cargo transport unit (e.g., by means of placement in racks, cabinets, etc.) N77 For materials of not more than two percent active ingredients by weight, packagings need not conform to the requirements of part 178 of this subchapter, if liquid contents are absorbed in an inert material. 350 Ammonium bromate, ammonium bromate aqueous solutions, and mixtures of a bromate with an ammonium salt are forbidden for transport. 28 The dihydrated sodium salt of dichloroisocyanuric acid does not meet the criteria for inclusion in Division 5.1 (Oxidizer) and is not subject to the requirements of this subchapter unless meeting the criteria for inclusion in another class or division. Metal: 11A, 11B, 11N, 21A, 21B and 21N, b. W9 When offered for transportation by water, the following Specification packagings are not authorized unless approved by the Associate Administrator: woven plastic bags, plastic film bags, textile bags, paper bags, IBCs and bulk packagings. 1/1.1 Flexible IBCs must be sift-proof and water-resistant or must be fitted with a sift-proof and water-resistant liner. 125 Lactose or glucose or similar materials may be used as a phlegmatizer provided that the substance contains not less than 90%, by mass, of phlegmatizer. Ammonia solutions may be transported in rigid or composite plastic IBCs (31H1, 31H2 and 31HZ1) that have successfully passed, without leakage or permanent deformation, the hydrostatic test specified in. The batteries inside the cargo transport unit are not subject to marking or labelling requirements of part 172 subparts D and E of this subchapter. 162 This material may be transported under the provisions of Division 4.1 only if it is packed so that at no time during transport will the percentage of diluent fall below the percentage that is stated in the shipping description. If not impact resistant, the outer packaging should not be used as the sole means of protecting the battery terminals from damage or short circuiting. A current copy of CGA pamphlet, CGA C-6 must be available at the facility servicing the life-saving appliance. 151 If this material meets the definition of a flammable liquid in 173.120 of this subchapter, a FLAMMABLE LIQUID label is also required and the basic description on the shipping paper must indicate the Class 3 subsidiary hazard. The objects must be secured to the flat car, motor vehicle, intermodal container, or unitized by steel banding to wooden runners or pallets and the units secured to the flat car, motor vehicle, or freight container to prevent shifting, including relative motion between the objects, under conditions normally incident to transportation. (iii) T50 When portable tank instruction T50 is indicated in Column (7) of the 172.101 Hazardous Materials Table, the applicable liquefied compressed gas and chemical under pressure descriptions are authorized to be transported in portable tanks in accordance with the requirements of 173.313 of this subchapter. Each transport unit must be leakproof when used as bulk packaging. 3 This material is poisonous by inhalation (see 171.8 of this subchapter) in Hazard Zone C (see 173.116(a) of this subchapter), and must be described as an inhalation hazard under the provisions of this subchapter. The table follows: [Portable tank codes T1-T22 apply to liquid and solid hazardous materials of Classes 3 through 9 which are transported in portable tanks.]. If a package contains both lithium metal batteries and lithium ion batteries packed with and contained in equipment, the package must be marked as required for both battery types. Each tank car must have a reclosing pressure relief device having a start-to-discharge pressure of 10.34 Bar (150 psig). 1 CFR 1.1 Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. Dry sodium cyanide or potassium cyanide is also permitted in siftproof, water-resistant, fiberboard IBCs when transported in closed freight containers or transport vehicles. The articles may be transported as in Division 1.4 Compatibility Group D (1.4D) if all of the conditions specified in 173.63(a) of this subchapter are met. The battery has been tested as a primary lithium battery; and. 65 The group of alkaline earth metals includes magnesium, calcium, strontium, and barium. Lithium ion cells and batteries at a state of charge greater than 30 percent of their rated capacity may only be transported under conditions approved by the Associate Administrator in accordance with the requirements in 49 CFR part 107, subpart H. Guidance and methodology for determining the rated capacity can be found in sub-section 38.3.2.3 of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter). c. Completed neutron radiation detection systems containing detectors meeting the conditions of paragraph a of this special provision must be transported as follows: (1) The detectors must be contained in a strong sealed outer casing; (2) The casing must contain include sufficient absorbent or adsorbent material to absorb or adsorb the entire gas contents; (3) The completed system must be packed in strong outer packagings capable of withstanding a 1.8 meter (5.9 feet) drop test without leakage unless a system's outer casing affords equivalent protection. (You can unsubscribe anytime), Learn More About USDOT/HazMat Transportation, generalpackaging requirements of173.24, Frequently Asked Questions Regarding the Regulations of the Resource Conservation and Recovery Act. will also bring you to search results. However, sediments remaining in the tank that meet the definition for a hazardous material are subject to the applicable regulations of this subchapter. While columns 8 and 7 of the Hazardous Materials Table are used to determine authorized packaging for most HazMat (more on that in a little bit), some methods of transportation, HazMat quantities, and specific operations rely on other methods. N91 The use of a non specification sift-proof, non-bulk, metal can with or without lid, or a non specification sift-proof, non-bulk fiber drum, with or without lid is authorized when transporting coal tar pitch compounds by motor vehicle or rail freight. contact the publishing agency. Each tank car must have a reclosing pressure relief device having a start-to-discharge pressure of 15.51 Bar (225 psig). Mass detonate means more than 90 percent of the devices tested in a package explode practically simultaneously. A56 Radioactive material with a subsidiary hazard of Division 4.2, Packing Group I, must be transported in Type B packages when offered for transportation by aircraft. A4 Liquids having an inhalation toxicity of Packing Group I are not permitted on aircraft. A2 Single packagings are not permitted on aircraft. Terminal protection methods include but are not limited to the following: (i) Securely attaching covers of sufficient strength to protect the terminals; (ii) Packaging the battery in a rigid plastic packaging; or. Symbols, if used, must be registered with the Associate Administrator. Background and more details are available in the These provisions apply only to bulk packagings. Amdt. For transportation by aircraft, as an inner packaging of a combination packaging with a maximum gross mass of 30 kg when packaged as a limited quantity in accordance with 173.27(f). Explosives shipped in conformance with this paragraph must have been examined in accordance with 173.56 of this subchapter and approved by the Associate Administrator. N92 Notwithstanding the provisions of 173.24(g) of this subchapter, packagings shall be designed and constructed to permit the release of gas or vapor to prevent a build-up of pressure that could rupture the packagings in the event of loss of stabilization. 64 The group of alkali metals includes lithium, sodium, potassium, rubidium, and caesium. N80 Packages consisting of one inner metal can, not over 2.5 kg (5.5 pounds) capacity, packed in an outer wooden or fiberboard box, or a wooden barrel, are authorized and need not conform to the requirements of part 178 of this subchapter. It must not freeze at temperatures above 15 C (5 F). N88 Any metal part of a UN pressure receptacle in contact with the contents may not contain more than 65% copper, with a tolerance of 1%. A13 Bulk packagings are not authorized for transportation by aircraft. TP6 The tank must be equipped with a pressure release device which prevent a tank from bursting under fire engulfment conditions (the conditions prescribed in CGA pamphlet S-1.2 (see 171.7 of this subchapter) or alternative conditions approved by the Associate Administrator may be used to consider the fire engulfment condition), taking into account the properties of the hazardous material to be transported.